LM566 DATASHEET PDF

0 Comments

This datasheet has been download from: Datasheets for electronics components. LM datasheet, LM circuit, LM data sheet: NSC – LMC Voltage Controlled Oscillator,alldatasheet, datasheet, Datasheet search site for Electronic. LM National Semiconductor datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic.

Author: Mezilabar Kagahn
Country: Bulgaria
Language: English (Spanish)
Genre: Automotive
Published (Last): 5 July 2014
Pages: 239
PDF File Size: 12.65 Mb
ePub File Size: 3.98 Mb
ISBN: 537-4-96946-944-9
Downloads: 4528
Price: Free* [*Free Regsitration Required]
Uploader: Dokazahn

If the modulation input is referred to ground e. The frequency modulation is lm5566 visible, as is the wave shape. It can be done using discrete transistors, but the end result would be quite complex, difficult to build, and would almost certainly have issues with thermal stability.

This applies whether the circuit is operated from a single or a dual supply. However, the frequency also depends on the threshold voltages for the Schmitt trigger U1B. Positive feedback is used to ensure that the triangle wave has a defined peak-to-peak voltage. The figure of Hz above datasheer only when the modulation lj566 is capacitively coupled as shown, and allows for the Despite appearances, the input will not be at zero volts when the pot is centred.

An opamp VCO circuit is shown in the LM opamp datasheet, and that’s the basis for the design shown here. This datashete seriously affect the transistor’s performance. For many applications, and especially for running frequency scans on speakers or crossover networks or any filters for that matteryou usually need at least a reasonable approximation of a sinewave. Sign up using Facebook. There aren’t many alternatives either. VCO Voltage controlled oscillator Voltage controlled oscillator is a type of oscillator where the frequency of the output oscillations can be ln566 by varying the amplitude of an input voltage signal.

  CPU 313C MANUAL PDF

Further, your statement is incorrect- the control voltage must be less than a maximum.

C1 is selected to give response down to the lowest frequency of interest, and is less than 1. While the LM is quite ok for a fairly basic VCO, it doesn’t scale well to higher frequencies above 5kHz or so because it’s a low power opamp with very basic specifications.

It is possible to recreate this in Multisim in a top level schematic using ideal components to see if it gives you the desired results with the shown external parts as well.

Because most are unable to pull the output voltage down to the negative supply, we need to add an extra resistor R9, Figure 3 to ensure that the transistor Q1 will turn on and off properly. A positive modulation voltage causes the frequency to increase, and vice versa.

Also your link is to the but your title and text says If you want to build any of the circuits shown, you’ll need to use Veroboard or similar.

So the question becomes, how to build one? The advantage of circuits like those shown here is that there are no glitches in the output, no matter how quickly or slowly the frequency is changed. You will need to experiment a little to get the frequency you need. It’s been assumed that you need a VCO with a triangle wave output that can be converted to a sinewave, and a squarewave with equal mark-space ratio.

Message 6 of 7. This is the frequency obtained when there is no external modulation.

  COMPAQ EVO D510 SFF MANUAL PDF

(PDF) LM566 Datasheet download

This isn’t needed for the LM, but is required for datasheeg other opamps that are a great deal faster. The datasheet shows a pair of fixed resistors, but I’ve shown a pot that lets datashset set the base frequency. A voltage controlled oscillator VCO isn’t something you need every day, and you may never have thought that you need one at all.

There are a few Datasheef phase locked loop ICs that are still available, but they aren’t especially easy to use. The ratio of R1 and R4, as well as R2 and R3 must be as shown for a triangle wave. Most Active Software Boards: For this, waveform purity isn’t a major concern, but you do need a constant amplitude regardless of frequency.

The input can be driven to greater than 12V, but with somewhat reduced linearity. In lmm566 you were wondering, the NE was never intended to be used as a modulator for FM radio.

The frequency change is related to the amplitude, and the rate-of-change is determined by the modulation frequency. The circuit diagram of a voltage controlled oscillator using LM is shown in the figure below.

pll – LM Frequency deviation problem – Electrical Engineering Stack Exchange

Unfortunately, the NE or LM which was an equivalent is no longer available from any reputable supplier. While using a single supply, the supply voltage range is from dayasheet to 24V. Message 5 of 7.

I need a circuit that does just the function 2 Wave of UTC http: