Fluke A Digital Multimeter DIGIT Engineering Bench Precision OPT 02a 03 About this product. About this product. Product Identifiers. BRAND. Fluke. Full text of “FLUKE A Instruction”. See other formats. Instruction Manual P/N MARCH 1 REV 1, 3/86 ®, John Fluke Mfg. Co., Inc. All Rights. Active Filter Block Diagram A Fast A/D Converter The Fast A/ D Converter employs Fluke’s patented recirculating remainder (R2) technique.

Author: Dougar Mim
Country: Nepal
Language: English (Spanish)
Genre: Relationship
Published (Last): 20 August 2014
Pages: 434
PDF File Size: 3.69 Mb
ePub File Size: 7.13 Mb
ISBN: 339-8-99744-414-7
Downloads: 95074
Price: Free* [*Free Regsitration Required]
Uploader: Neshicage

Thermal emfs voltages produced by temperature differences between contacts of two dissimilar metals or by temperature gradients along a length of material ‘ may cause differences of several microvolts.

Therefore, commands SO through SI 7 or HO through H9 cannot be used for sample settings when the A is set for ac volts normal, enhanced, or high accuracy. The line fuse 0.

Considerable versatility is realized through unique contruction. Special instructions for inspection and claims are included with the shipping container. Default Configurations The multimeter identifies its own software and hardware at initial turn-on. Final claim and negotiations with the carrier must be completed by the customer.

Full text of “FLUKE a”

The error message may be returned repeatedly. A numeric value may be entered using a store sequence. Clearall of Calibration Memory. Measurement Instructions The lowest-priced item that has been used or worn previously.


Proper use of a floating, guarded multimeter minimizes these errors. Speed of measurement is fluuke important.

Fluke 8505A FOR RENT

Each error code contains twodigits: This eight-section manual provides comprehensive information for installing, operating and mainta inin g your Fluke digital multimeter. One variety includes dc volts Vohms Zand dc amps I. The “D” command characters turn the DMM front panel display on or off. For example, in the A, “HI For example, if the displayed value is being used to zero the multimeter, it is important to verify that no other mathematic operations are in effect.

Pushing ZERO a second time disables the mode, but retains the previousvalue. Further programming from the front panel is often not necessary.

Up to readings a second are possible when using High Speed Ohms.

Front Panel Push Fluuke cont A Selection of any filter other than F or F2 is accepted by the multimeter, but causes deactivation of Averaging mode.

Power off, remove one ac converter, or install correct converter, or remove the Calibration Memory module the multimeter uses a separate Calibration Memory as part of the Controller.

The read value may not be stored as a Scaling Factor. Zero mode is off.

If the same function is re- selected, the state of Average mode is not changed, and the existing fiiter mode and sampie setting are retained. Noise rejection is influenced by the number of samples-per-reading and by the filter selection.


This time-out causes a deiay ffluke a trigger command received and the actual reading taken. Reselecting V DC sets autoranging.

The function module selected is faulty or not installed. With the initial button push, a new zero value is stored and the mode is enabled ZERO annunciator on. The fost filter FO is always selected when a slow filter F or F2 is in effect. The multimeter adopts both the mode specified with the terminator and the value previously displayed.

Outputs from the optional ac converter modules are applied to the Active Filter module, bypassing the DC Signal Conditioner.

Fluke 8505A Multimeters

The multimeter front panel display is blank while High Speed mode is on. If Calibration mode is on, the zero value is stored for the range selected without affecting the value for any other range. Ohms Converter Option A 3: Response includes six digits with no leading zero suppression.